Washing Machine Filter: How Often to Clean It

There is a small hatch at the bottom front of almost every washing machine sold in the UK, usually behind a flap or a clip-off panel. Behind it is a filter. Ask around and a clear majority of people have never opened it, including people who have owned the same machine for a decade.

What comes out the first time is memorable, and not in a good way.

The Short Answer

Clean it every three months for an average household. Every month if you have pets, wash a lot of towels, or have small children whose pockets contain the entire contents of a beach.

The filter sits in front of the drain pump and catches anything that gets through the drum — coins, hair grips, buttons, tissue, pet hair, lint, and the occasional sock. Its job is to stop those things reaching the pump impeller. When it clogs, drainage slows, and slow drainage lengthens every cycle and eventually stops the machine with an error.

Set a reminder, because there's no warning light and no symptom until it's already causing problems. Five minutes, four times a year.

What Actually Matters

The filter is doing two jobs, and only one of them is obvious.

The obvious one is mechanical protection. A drain pump has a small plastic impeller spinning at speed. A 5p piece in that impeller either jams it or chips the blades, and a pump replacement is £80-£150 fitted. The filter is a £0 part protecting an expensive one.

The less obvious job — and the one that affects daily life more — is that the filter housing is where residual water sits between washes. Every machine retains a small amount of water there by design. Add lint, hair and detergent residue and you have a warm, damp, nutrient-rich environment that grows biofilm: the grey-black, slightly greasy deposit that produces the musty smell people blame on the door seal.

The seal usually gets the blame because that's the part you can see. In a machine that smells, the filter housing is at least as often the source, and cleaning the seal without cleaning the filter is why the smell keeps coming back.

Detailed Analysis

How to do it without soaking the kitchen floor

The mistake everyone makes once is unscrewing the filter cap and discovering there's a litre of water behind it. Machines vary in how much they hold, but plan for it.

The method:

  • Switch off at the wall and let the machine cool if it's just run a hot wash.
  • Lay old towels along the floor in front of the machine, and have a shallow tray or roasting tin ready.
  • Look for a short drain hose beside the filter cap — most machines have one. Pull it out, remove its bung, and drain into the tray first. This is the step that saves the towels.
  • Once the flow stops, unscrew the filter cap anticlockwise. Expect a bit more water regardless.
  • Pull the filter out, clear the debris, and rinse it under a tap. An old toothbrush gets the mesh clean.
  • Reach into the housing and clear anything sitting in there. Wipe the inside with a cloth — this is where the biofilm lives.
  • Check the impeller you can see at the back of the housing turns freely with a finger. It should spin with slight resistance.
  • Refit, screwing until firm. Not overtightened — the seal does the work.

Run a short rinse cycle afterwards and check underneath for drips. A filter that isn't seated properly leaks slowly and you want to know immediately.

What you'll actually find

Coins, hair grips, buttons, screws, underwiring from bras, small toys, and an alarming quantity of grey felt made of fabric fibres, hair and detergent residue. In a house with a cat or a long-haired dog, mostly hair.

The underwiring case deserves a mention because it's the one that causes real damage. A bra wire that escapes the garment can pass through the drum's perforations and end up between the drum and the outer tub, where it rattles horribly and can puncture the tub. If you find one in the filter, that's the lucky outcome. Wash bras in a mesh laundry bag and the problem disappears.

How a blocked filter shows up elsewhere

This is the useful part, because a blocked filter rarely announces itself directly. It shows up as other faults:

Cycles taking longer than they used to. The machine drains between phases; if draining is slow it waits, retries, and adds time to every stage.

Clothes wetter than normal at the end. Water not fully removed before the spin means the spin starts against a partially full tub and the machine reduces speed for balance.

Drain error codes. Most manufacturers have one — F05 on Hotpoint, E20 or 5E on Samsung, and various others. The manual's first instruction is almost always to check the filter, precisely because it's the most common cause.

Water left in the drum. The obvious one, and by then it's well past due.

The musty smell. As above — biofilm in the filter housing is a major contributor and it's the part nobody cleans.

Machines without an accessible filter

A small number of models, mostly integrated and some Bosch and Miele designs, have the filter behind the kickplate or in a less obvious position, and a very few have no user-accessible filter at all — the pump is protected by a trap that needs an engineer.

If you can't find a hatch on the front, check behind the plinth or kickplate first, then the manual. Don't assume there isn't one; assume it's hidden, because on the overwhelming majority of machines it exists.

Real-World Considerations

Frequency should follow your household rather than a rule. Pets are the single biggest variable — a house with a moulting dog can block a filter in six weeks. Towelling and new fleecy items shed heavily for their first several washes. Very hard water areas accumulate more residue because detergent and scale combine into a sludge that coats everything.

Timing it with something else helps. Doing the filter at the same time as a hot maintenance wash — 90°C, empty drum, machine cleaner or soda crystals — makes a sensible quarterly routine, and the two jobs address the same underlying problem from different directions.

Worth knowing for anyone in rented accommodation: a blocked filter causing a flood is generally considered a maintenance failure rather than an appliance fault, and letting agents do occasionally push back on repair costs on that basis. Five minutes a quarter is cheap insurance against that argument.

One last point on the money. A drain pump replacement runs £80-£150 with labour, and pump failure caused by debris is the most common washing machine repair after bearings. On a machine over eight years old, that repair often tips into replace-instead territory. The filter is the cheapest preventative maintenance available on any appliance in the house.

Common Mistakes Buyers Make

Opening the cap without draining first. A litre of dirty water across the kitchen floor, and it's entirely avoidable using the small drain hose beside the cap.

Cleaning the filter but not the housing. The biofilm causing the smell is on the inside of the housing, not on the filter mesh.

Overtightening on refitting. Firm is enough. Overtightening distorts the seal and causes the leak you were trying to prevent.

Only doing it when there's a fault. By the time water is sitting in the drum, the pump has already been working against a restriction for weeks.

Not checking the impeller. A quick finger-turn confirms nothing is jammed. It takes two seconds and it's the whole reason the filter exists.

Alternatives Worth Considering

Nothing replaces the filter clean, but a few habits reduce how much reaches it. A mesh laundry bag for bras, delicates and anything with small parts keeps underwiring and buttons out of the system entirely. Emptying pockets properly is obvious and rarely done.

For pet owners, running an empty rinse after a heavy pet-bedding wash flushes a good proportion of loose hair through before it settles. Pet hair-catching laundry balls exist and do work moderately well, though they're no substitute for opening the filter.

If your machine genuinely has no accessible filter, the sensible approach is a service call every couple of years rather than waiting for a pump failure. That's an unusual design and worth confirming in the manual before accepting it.

Frequently Asked Questions

Where is the filter on a washing machine?

Bottom front, behind a small flap or a clip-off panel, usually on the right. On some integrated models it sits behind the kickplate.

What happens if you never clean it?

Drainage slows, cycles lengthen, and eventually the machine stops with a drain error. Debris reaching the pump impeller can cause a failure costing £80-£150 to repair.

Why does my washing machine filter smell?

Residual water sits in the housing between washes, and combined with lint and detergent residue it grows biofilm. That's frequently the real source of a musty machine, rather than the door seal.

How do I stop water going everywhere?

Use the short drain hose beside the filter cap to empty into a tray first. Most machines have one, and it's the step almost everyone misses the first time.

Can I clean it while the machine is full of water?

Better not to. If the machine has stopped mid-cycle with a full drum, run a spin or drain programme first if it will, or siphon the drum down before opening the filter.

Final Thoughts

Quarterly for most households, monthly with pets. Drain the hose first, clean the housing as well as the mesh, check the impeller turns, and don't overtighten on the way back.

It's five minutes of genuinely unpleasant work that prevents the most common expensive repair on the machine, and it fixes a smell most people spend money on chemical treatments trying to solve. Few maintenance jobs in a house have a better return.

Post a Comment

Previous Post Next Post