How to Dry Washing in a Flat With No Outdoor Space

From about the end of September, a flat with no balcony and no tumble dryer becomes a drying problem. The washing has to go somewhere, and wherever it goes it releases around two litres of water per load into a space that has very little natural ventilation.

That water does not vanish. It condenses on the coldest surface in the flat, which is usually a window reveal, an external wall behind a wardrobe, or the corner of a bedroom. Do it three times a week through a winter and you get mould.

The Short Answer

Contain it, then vent it. One room, door closed, window on the latch or an extractor running. That is the whole method and it costs nothing.

The full routine:

  • Spin at the highest speed the fabric allows. This is free and it removes water mechanically before it ever becomes airborne.
  • Dry in one room only — ideally the bathroom if it has an extractor, otherwise the coolest room you can spare. Not a bedroom.
  • Shut the door. Otherwise the moisture migrates through the flat and finds every cold surface.
  • Open a window a crack, or run the extractor. The moisture has to leave the building, not just move around it.
  • Space the load out. Items touching each other take three days instead of one, and they release moisture for all three.

Never dry on radiators. It releases moisture fastest into the room you are sitting in, and it blocks the heat you are paying for.

If you are doing this all winter, a dehumidifier is the proper answer. It collects the water instead of moving it around, and it runs for a fraction of what a tumble dryer costs.

What Actually Matters

How much water is involved. An 8kg load spun at 1400rpm holds roughly four kilograms of water when it comes out. Some drips away; a large part of it — commonly around two litres — evaporates into your flat.

Three loads a week is six litres a week going into the air of a space that, in a modern well-sealed flat, exchanges very little air with outside. That is the whole problem in one sentence.

Where it condenses. Warm air holds more moisture than cold air. Humid air moves through the flat until it meets a surface below its dew point — single glazing, an uninsulated external wall, the cold spot behind furniture — and deposits its water there. Repeated condensation on the same surface is what grows mould.

Spin speed, which almost nobody adjusts. Every litre the washing machine removes mechanically is a litre that never enters your air and never needs drying. It costs essentially nothing to spin faster, and it is the single most effective change available.

Detailed Analysis

Why containing it works

Shutting a door and opening a window feels contradictory when you are trying to heat a flat. The arithmetic holds up anyway.

Moisture moves from where there is more of it to where there is less. Left to circulate, the humidity from your drying washing will find the coldest surface in the flat, and that is rarely in the room the airer is in. It is behind a wardrobe on an external wall, or on a bedroom window, or in the corner of a north-facing room.

Closing the door confines the humidity to one room. Opening a window in that room gives it somewhere to go that is not your bedroom wall. The heat lost through one window on the latch for a few hours is small. The cost of treating mould on a bedroom wall, or of a deposit dispute about it, is not.

Choose the room deliberately. A bathroom with a working extractor is the best option most flats have — it is designed to handle moisture and it usually has mechanical ventilation. A hallway works. A spare room works. A bedroom does not, because you will then sleep in the humidity.

Getting the water out before it becomes airborne

Worth doing first because it reduces everything downstream.

Residual moisture after a spin varies substantially with speed. A 1000rpm spin leaves cottons at roughly 60% residual moisture; 1400rpm at around 50%; 1600rpm a little under. Those figures translate directly into how much water ends up in your flat and how long the load takes to dry.

For towels, bedding and everyday cottons, use the highest spin the machine offers. The creasing penalty is real and modest, and it is a smaller problem than condensation.

An extra spin cycle on a load destined for an indoor airer takes a few minutes and negligible electricity, and it can be the difference between a load drying overnight and a load drying over three days.

Load size matters too. An overpacked drum does not spin efficiently, so the load comes out wetter. Two-thirds full is the target, covered in how full a washing machine drum should be.

Dehumidifiers, and what they cost

For a flat with no outdoor space, this is the intervention that actually solves the problem rather than managing it.

A dehumidifier removes water from the air and collects it in a tank. Unlike ventilation, it does not need you to open anything in January. Unlike a tumble dryer, it does not need a vent or much electricity.

Typical domestic models draw between 150W and 500W. At the Ofgem capped rate of 26.32p per kWh for 1 October to 31 December 2026 — substitute your own rate — running a 300W unit for six hours costs about 47p. A vented tumble dryer load costs around £1.05 at the same rate.

Most have a laundry or continuous mode that runs the fan harder and ignores the humidity target. That is the setting for drying washing.

Two types exist and the difference matters in a cold flat. Compressor models are more efficient in warm rooms. Desiccant models keep working properly below about 15°C, which covers a lot of unheated British hallways and spare rooms in winter. For a cold flat, desiccant is usually the better buy despite being slightly less efficient on paper.

The other benefit is that you can see the result. A dehumidifier running alongside drying washing fills its tank, and looking at a litre and a half of collected water is a fairly convincing demonstration of what would otherwise have gone onto your windows.

Heated airers, the middle option

A heated airer is a rack with low-wattage heating elements in the bars, typically drawing 100-300W. They speed up drying substantially compared with an unheated airer, and with a cover over the top they become something close to a slow, cheap tumble dryer.

They are genuinely well suited to flats: no vent, no plumbing, they fold away, and running one for four hours costs around 20-30p.

The important caveat is that a heated airer still releases the moisture into the room. It dries the washing faster; it does not remove the water from your flat. The ventilation advice above applies in full.

Used together, a heated airer and a dehumidifier in the same closed room is the most effective arrangement available without a dryer — one drives the water out of the fabric, the other collects it.

If a dryer is an option at all

Flats without outdoor space are exactly where ventless dryers earn their place, and a heat pump model is the one to look at.

It needs no hole in the wall, unlike a vented dryer. And unlike a condenser dryer it runs at a much lower drum temperature, so it releases noticeably less warmth and humidity into a small flat. Running costs are roughly a third of a vented machine's, discussed in condenser versus heat pump running costs.

The trade is time — three hours rather than one, covered in how long a tumble dryer should take. In a flat where the machine runs while you are at work, that rarely matters.

Real-World Considerations

Modern flats can be worse than older ones for this, which surprises people. A well-sealed, well-insulated building has very little accidental ventilation, so moisture put into it tends to stay. If you have moved from a draughty house to a new-build flat and suddenly have condensation, that is usually why.

Trickle vents on modern windows exist for exactly this and are routinely closed or taped over because of draughts. Opening them in the drying room is free and helps.

Bathroom extractors are worth checking rather than assuming. Many run only with the light, some are blocked with dust, and a few were never connected to anything. Hold a sheet of tissue against the grille with the fan on — if it does not hold, the fan is not moving air.

Renting adds a dimension worth knowing about. Landlords sometimes attribute condensation to drying washing indoors, and tenants point to inadequate ventilation. Both can be partly right. The current legal position is that a landlord generally cannot attribute damp to tenant lifestyle unless they can show that is the sole cause, and the building's ventilation provision is their responsibility. Keeping a record of what you do — which room, window open, extractor running — is genuinely useful if that conversation ever happens.

Watch for the early signs rather than waiting for mould. Condensation on the inside of windows in the morning, a musty smell in a particular room, or a wall that feels cold and slightly damp to the touch all indicate the moisture is not leaving.

And if a load takes more than about a day to dry, the arrangement is wrong rather than the weather. Usually it is spacing — an airer packed so items touch takes three times as long and releases moisture for all of it.

Common Mistakes Buyers Make

  • Drying on radiators. Fastest possible moisture release into a living space, plus a heating system working harder for the same room temperature.
  • Drying in a bedroom with the door open. The humidity migrates and finds the coldest wall, which is often in that same bedroom.
  • Keeping every window shut to save heat. The moisture has to leave somehow. One window on the latch in one room costs very little.
  • Spinning at low speed to protect clothes. Every litre left in the load ends up in your flat and extends the drying time.
  • Packing the airer. Items touching dry slowly and keep releasing moisture for days.
  • Buying a compressor dehumidifier for a cold hallway. Desiccant models perform far better below about 15°C.
  • Assuming the bathroom extractor works. Test it with a tissue. A lot of them do not move air.
  • Treating mould as a cleaning problem. Wiping it off without changing the moisture source means it comes back in the same place.

Alternatives Worth Considering

A heated airer with a cover is the cheapest meaningful upgrade for a flat. Around 20-30p a load, folds away, needs no installation, and it roughly halves drying time.

A desiccant dehumidifier is the right answer for an unheated flat or a cold spare room, and it addresses the cause rather than the symptom. It also helps with general winter condensation, which is a second benefit for the same running cost.

A heat pump tumble dryer is worth considering if there is space for one, since it needs no external vent and puts far less warmth and moisture into a small flat than a condenser model does.

And if none of those fit, spreading loads across the week rather than doing three on a Sunday keeps the peak humidity manageable. Two litres a day a flat can cope with. Six litres in an afternoon it cannot.

Frequently Asked Questions

How do you dry clothes in a flat with no outdoor space?

In one room with the door shut and a window on the latch or an extractor running. Spin the load at the highest speed the fabric allows first.

Does drying clothes indoors cause damp?

It adds around two litres of water per load to the air. Whether that becomes damp depends entirely on whether it is ventilated out or allowed to condense on cold surfaces.

Is a dehumidifier cheaper than a tumble dryer?

Considerably. Six hours of a 300W dehumidifier costs under 50p at current capped rates, against around £1 for a vented dryer load.

Which dehumidifier works in a cold flat?

A desiccant model. Compressor dehumidifiers lose efficiency below about 15°C, which covers most unheated rooms in a British winter.

Can you dry clothes in a bathroom?

It is often the best room available, provided the extractor actually works and the door stays shut.

How long should washing take to dry indoors?

Under a day with a fast spin, good spacing and ventilation. Longer than that means the load is packed too tightly or the room is not venting.

Final Thoughts

The instinct in a cold flat is to close everything and let the heating deal with it, and that is exactly the combination that produces mould on a bedroom wall by February.

Contain the washing in one room, give that room a way to breathe, and spin the load hard before it comes out of the machine. Those three habits handle most of it for nothing at all.

If you are drying indoors every winter, a dehumidifier pays for itself quickly — both against a tumble dryer and against what it prevents on the walls. For the general version of this problem, see drying clothes indoors without causing damp, and if the washing has already started to smell, getting the damp smell out of clothes.

Post a Comment

Previous Post Next Post